Cut out plate Design

 Wednesday(26/04/2023)

Enameled plate with pierced lotus

This is an enameled plate with a pierced out lotus design that has been inserted into the kiln which fused the lotus onto the enameled plate and has been cleaned in sulphuric acid before inserting enamel into the specific parts of the lotus design. 

Amethyst enamel powder added 

This is the outcome of the amethyst enamel cooled down from the kiln.

 Green Enamel added to design

This is what the enamel powder looks when it is applied onto the piece. The powder has been mixed with a small amount of water. 

The final look of the design

Exploring design with enamling

Wednesday(26/04/2023)

Stencil

 

I was watching a tutorial video on enameling when I came across the idea of a stencil being used to add design onto the enamel, so I decided to create a mendhi design stencil. 

Designed on a piece of paper and then used a wax blade to do the cut outs of the design. 

Stencil design on plate

The stencil was placed onto the enameled plate that an opaque green as the background and I had then sifted the enamel powder onto the stencil to get the design onto the plate, inserted into the kiln and then waited for 1-2 min for the enamel to fuse onto the metal. 

Final: stenciled design

This is the final outcome once it has been removed from the kiln and cooled. 

Enameling :colour Powder

Tuesday(25/04/2023)

Enamel powder

Enamel powder is powdered glass and comes in varieties of colour.

Enamel powder and sift

The enameled powder comes in different ranges, Opaque and transparent as well as the different temperatures needed for the enameling fusing process. 

Before adding the enameled powder onto the other side you should put the copper plate once again into the acid as the oxide that has formed after the backing enamel process as the enamel will not fuse if there is oxide visible on the plate. 

Enameled plate

This is how the final outcome looks once it has cooled from the kiln.

Lotus designed with copper wire

Enamel powder with slight water added

Paint brush to add enamel in specific parts of the design.

Once the enamel is added, dab a small piece of tissue onto the wet enamel to drain abit of the water and keep the plate near the kiln to dry the enamel before adding into the kiln as it could evaporate and the enamel would not catch onto the design. 

Final look

Backing Enamel:

 Tuesday (25/04/2023)

Backing Enamel. 

Backing Enamel is a mixture of all the extra bits of enamel powders.

Backing Enamel with sift

Step 1:The backing enamel powder is then sifted onto the metal which will then be inserted into the kiln, only if the kiln has reached maximum temperature. 

Backing powder sieved onto the copper plate

step 2: The wait for piece in the kiln takes about 2-3 min depending on the size of the piece and the heat.

Enameled plate out of the kiln on the stand

Step 3: It would start looking like an orange peel texture but it would be preferable to have a smooth texture.

Backing enamel after inserted in kiln and cooled. 

Step 4: Use the steel fork to lift the stand holding the enameled plate from the kiln, the place the enameled plate on the steel block and press the enameled plate with the grip pointed trowel to cool the metal and flatten the piece. 

Step 5: Once the metal has cooled, this is the outcome.(Ref:image above)

Enameling: Experiment: The Kiln set up

 Tuesday(25/04/2023):

Kiln 

Step 1: This is the kiln where the heating process by which powdered glass is fused to metal substrate at high heat. 

Step 2: Check that the main plug is on to switch the kiln on. Then set the kiln temperature to 800 degrees.

Step 3: Wait for the kiln to reach the set temperature before inserting any pieces to be enameled. 

Enameling Experiment: Metal Prep

On Tuesday(25/04/2023) I began the enameling experimentation. This is how it all went down: 

Scrap Copper Metal 

Step 1: Collected scrap copper metal and cut them into appropriate sizes needed for the experiment.

Cut,Cleaned copper

Step 2: Cleaning the copper with acid to remove the grease and other forms that could resist for the enamel to stick onto the metal therefore you clean the metal with Sulphuric Acid and give it a good clean. Once it is cleaned, try not to touch the plate or cut out metal much as oils would make contact again with the metal. Preferable to hold the corners of the plate. 

Henna Design on Body

 After experimenting with the Henna on a tissue I just decided to doodle a design on my arm...I always asked why I do it on my wrist and on one hand only, this is because I like the look of it playing a role of a tattoo as I would never want to ink my body permanently. These are the processes of getting the final look:

The Henna Tube containing dried leaves made into a paste

What it looks like when you apply the Henna on your body 

The outcome once it has been dried and rinse the dried Henna.

(the longer you wait for the Henna to dry the darker it stains)

What it looks like the next day, it actually starts to darken(tip is to apply vicks)